Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Ragnarok" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Ragnarok" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Surtr in Muspelheim" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Surtr in Muspelheim" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take up to two weeks before shipping)

“American Flag" Full-Tank Decal for Indian Scout models

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take up to two weeks before shipping)

“American Flag" Full-Tank Decal for Indian Scout models

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take approximately two+ weeks before shipping)

“Autumn-2023" Indian Scout Tank Decals

These decals were designed to fit on the side of the Indian Scout tank (all models).  If your tank has a pre-existing design, we cannot guarantee this decal will cover it.  Please look at the product thumbnail that shows how it fits on the tank side to determine if this decal is for you.

Size: Will be posted soon

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Bear" Full-Tank Decal for Indian Scout models

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take up to two weeks before shipping)

“Bear" Full-Tank Decal for Indian Scout models

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take approximately two weeks before shipping)

“Fenrir" Universal Tank Decals for all Brands and Models of Motorcycles

This design was custom commissioned and our client has graciously allowed us to share it with other customers.

Size: 15.26 x 5.85 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank.

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock but may take 2-3 weeks before shipping if not in stock at the time of your order.

“Fenrir" Full-Tank Decal for Indian Scout models

This design was custom commissioned and our client has graciously allowed us to share it with other customers.

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

'Bronze' is not a metallic finish. This is a printed DTF material as described below.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

'GOLD' accents are not metallic. This is a printed DTF material with a semi-gloss finish.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

'Gun Metal' is not metallic. This is a printed DTF material as described below.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

New Item - Special Order (may take up to two weeks before shipping)

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

New Item - Special Order (may take approximately two+ weeks before shipping)

“Kateri-2023" Indian Scout Tank Decals

These decals were designed to fit on the side of the Indian Scout tank (all models).  If your tank has a pre-existing design, we cannot guarantee this decal will cover it.  Please look at the product thumbnail that shows how it fits on the tank side to determine if this decal is for you.

Size: Will be posted soon

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take approximately two+ weeks before shipping)

“Kateri-2023" Indian Scout Tank Decals

These decals were designed to fit on the side of the Indian Scout tank (all models).  If your tank has a pre-existing design, we cannot guarantee this decal will cover it.  Please look at the product thumbnail that shows how it fits on the tank side to determine if this decal is for you.

Size: Will be posted soon

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take approximately two+ weeks before shipping)

“Lilith-2023" Indian Scout Tank Decals

These decals were designed to fit on the side of the Indian Scout tank (all models).  If your tank has a pre-existing design, we cannot guarantee this decal will cover it.  Please look at the product thumbnail that shows how it fits on the tank side to determine if this decal is for you.

Size: Will be posted soon

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take approximately two+ weeks before shipping)

“Lilith-2023" Indian Scout Tank Decals

These decals were designed to fit on the side of the Indian Scout tank (all models).  If your tank has a pre-existing design, we cannot guarantee this decal will cover it.  Please look at the product thumbnail that shows how it fits on the tank side to determine if this decal is for you.

Size: Will be posted soon

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take approximately two+ weeks before shipping)

“Maya-2023" Indian Scout Tank Decals

These decals were designed to fit on the side of the Indian Scout tank (all models).  If your tank has a pre-existing design, we cannot guarantee this decal will cover it.  Please look at the product thumbnail that shows how it fits on the tank side to determine if this decal is for you.

Size: Will be posted soon

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take approximately two+ weeks before shipping)

“Meadow-2023" Indian Scout Tank Decals

These decals were designed to fit on the side of the Indian Scout tank (all models).  If your tank has a pre-existing design, we cannot guarantee this decal will cover it.  Please look at the product thumbnail that shows how it fits on the tank side to determine if this decal is for you.

Size: Will be posted soon

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take approximately two+ weeks before shipping)

“Mermaid 1-2023" Full-Tank Decal for Indian Scout models

This design is an ode to my wife @TropicalBobber. Her mermaid themed Scout Bobber Sixty was decorated with the first mermaid art I ever created.  She’s since moved on to a Chieftain Limited and is ready to allow others to explore the theme, though the mermaid art I now offer, is different than hers was. - Jason

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.