Products

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Ragnarok" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Ragnarok" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Surtr in Muspelheim" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Surtr in Muspelheim" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take up to two weeks before shipping)

“Altered Carbon” 

Part of our new lineup of Designer Series decals that take a step away from our traditional themes to bring you more options.

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

New Item - Special Order (may take up to two weeks before shipping)

“American Flag" Full-Tank Decal for Indian Scout models

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take up to two weeks before shipping)

“American Flag" Full-Tank Decal for Indian Scout models

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

The Aztec Jaguar God of the Underworld is featured on our Azteca fuel tank decals!  They were designed to fit stylishly on the side of the Indian Scout’s fuel tank and give you a large and unique piece of art to really set your bike apart from the others. 

Size: Approximately 15 x 5 inches (NOT large enough to cover the Challenger's logo or the Scout Twenty full tank side graphic).  The size and shape of this decal is designed to fit the side of the Scout fuel tank.  It has been used on other bikes (see photos), but does not completely cover OEM warbonnet.

Fits: 

• Scout (Scout 86 from 1993-94, Scout from 2001-2002, Scout from 2014-Present (all models except the Bobber Twenty).  See photos for example of the fit

Photo courtesy of Shadowfax_the_Scout

The Aztec Jaguar God of the Underworld is featured on our Azteca fuel tank decals!  They were designed to fit stylishly on the side of the Indian Scout’s fuel tank and give you a large and unique piece of art to really set your bike apart from the others. 

Size: Approximately 15 x 5 inches (NOT large enough to cover the Challenger's logo or the Scout Twenty full tank side graphic).  The size and shape of this decal is designed to fit the side of the Scout fuel tank.  It has been used on other bikes (see photos), but does not completely cover OEM warbonnet.

Fits: 

• Scout (Scout 86 from 1993-94, Scout from 2001-2002, Scout from 2014-Present (all models except the Bobber Twenty).  See photos for example of the fit

Photo courtesy of Taro Seo

New Item - Special Order (may take up to two weeks before shipping)

“Bear" Full-Tank Decal for Indian Scout models

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take up to two weeks before shipping)

“Bear" Full-Tank Decal for Indian Scout models

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

New Item - Special Order (may take up to two weeks before shipping)

“Bolt” 

Part of our new lineup of Designer Series decals that take a step away from our traditional themes to bring you more options.

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

New Item - Special Order (may take up to two weeks before shipping)

“Bomber” 

Part of our new lineup of Designer Series decals that take a step away from our traditional themes to bring you more options.

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

View this post on Instagram

A post shared by Brave Wolf Customs (@bravewolfcustoms)

CLEARANCE

NO REFUNDS - BUY AT YOUR OWN RISK - EXPLANATION FOLLOWS:

After multiple reports from customers, I’ve discovered that the factory finishing process on the Scout engines varies more than anticipated. While the black-coated surface is consistently present, the bare metal accents are manually ground down at the factory, and the level of grinding differs significantly from bike to bike. This results in variations in width, length, and positioning that I hadn’t encountered in other motorcycle models using the same accent kit design.
When I originally created the template, I used an in-shop Scout engine as the reference, but because of the inconsistent factory finishing, some customers are experiencing partial exposure of the bare metal accents beyond the kit’s coverage area. Additionally, the left-side horizontal accents on many Scouts are shorter than the right side by approximately 12-14mm, which required a unique two-piece installation approach. While that adjustment worked in many cases, the additional issue of varying grinding depths has made it impossible to ensure a consistent, proper fit for all bikes.
Because of this, I’ve made the difficult decision to discontinue this product for the Scout lineup to avoid further frustration. Some customers get a perfect fit. Others may find that some of the bare metal is still visible.

_________

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

CLEARANCE

NO REFUNDS - BUY AT YOUR OWN RISK - EXPLANATION FOLLOWS:

After multiple reports from customers, I’ve discovered that the factory finishing process on the Scout engines varies more than anticipated. While the black-coated surface is consistently present, the bare metal accents are manually ground down at the factory, and the level of grinding differs significantly from bike to bike. This results in variations in width, length, and positioning that I hadn’t encountered in other motorcycle models using the same accent kit design.
When I originally created the template, I used an in-shop Scout engine as the reference, but because of the inconsistent factory finishing, some customers are experiencing partial exposure of the bare metal accents beyond the kit’s coverage area. Additionally, the left-side horizontal accents on many Scouts are shorter than the right side by approximately 12-14mm, which required a unique two-piece installation approach. While that adjustment worked in many cases, the additional issue of varying grinding depths has made it impossible to ensure a consistent, proper fit for all bikes.
Because of this, I’ve made the difficult decision to discontinue this product for the Scout lineup to avoid further frustration. Some customers get a perfect fit. Others may find that some of the bare metal is still visible.

_________

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

CLEARANCE

NO REFUNDS - BUY AT YOUR OWN RISK - EXPLANATION FOLLOWS:

After multiple reports from customers, I’ve discovered that the factory finishing process on the Scout engines varies more than anticipated. While the black-coated surface is consistently present, the bare metal accents are manually ground down at the factory, and the level of grinding differs significantly from bike to bike. This results in variations in width, length, and positioning that I hadn’t encountered in other motorcycle models using the same accent kit design.
When I originally created the template, I used an in-shop Scout engine as the reference, but because of the inconsistent factory finishing, some customers are experiencing partial exposure of the bare metal accents beyond the kit’s coverage area. Additionally, the left-side horizontal accents on many Scouts are shorter than the right side by approximately 12-14mm, which required a unique two-piece installation approach. While that adjustment worked in many cases, the additional issue of varying grinding depths has made it impossible to ensure a consistent, proper fit for all bikes.
Because of this, I’ve made the difficult decision to discontinue this product for the Scout lineup to avoid further frustration. Some customers get a perfect fit. Others may find that some of the bare metal is still visible.

_________

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

CLEARANCE

NO REFUNDS - BUY AT YOUR OWN RISK - EXPLANATION FOLLOWS:

After multiple reports from customers, I’ve discovered that the factory finishing process on the Scout engines varies more than anticipated. While the black-coated surface is consistently present, the bare metal accents are manually ground down at the factory, and the level of grinding differs significantly from bike to bike. This results in variations in width, length, and positioning that I hadn’t encountered in other motorcycle models using the same accent kit design.
When I originally created the template, I used an in-shop Scout engine as the reference, but because of the inconsistent factory finishing, some customers are experiencing partial exposure of the bare metal accents beyond the kit’s coverage area. Additionally, the left-side horizontal accents on many Scouts are shorter than the right side by approximately 12-14mm, which required a unique two-piece installation approach. While that adjustment worked in many cases, the additional issue of varying grinding depths has made it impossible to ensure a consistent, proper fit for all bikes.
Because of this, I’ve made the difficult decision to discontinue this product for the Scout lineup to avoid further frustration. Some customers get a perfect fit. Others may find that some of the bare metal is still visible.

_________

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

CLEARANCE

NO REFUNDS - BUY AT YOUR OWN RISK - EXPLANATION FOLLOWS:

After multiple reports from customers, I’ve discovered that the factory finishing process on the Scout engines varies more than anticipated. While the black-coated surface is consistently present, the bare metal accents are manually ground down at the factory, and the level of grinding differs significantly from bike to bike. This results in variations in width, length, and positioning that I hadn’t encountered in other motorcycle models using the same accent kit design.
When I originally created the template, I used an in-shop Scout engine as the reference, but because of the inconsistent factory finishing, some customers are experiencing partial exposure of the bare metal accents beyond the kit’s coverage area. Additionally, the left-side horizontal accents on many Scouts are shorter than the right side by approximately 12-14mm, which required a unique two-piece installation approach. While that adjustment worked in many cases, the additional issue of varying grinding depths has made it impossible to ensure a consistent, proper fit for all bikes.
Because of this, I’ve made the difficult decision to discontinue this product for the Scout lineup to avoid further frustration. Some customers get a perfect fit. Others may find that some of the bare metal is still visible.

_________

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

CLEARANCE

NO REFUNDS - BUY AT YOUR OWN RISK - EXPLANATION FOLLOWS:

After multiple reports from customers, I’ve discovered that the factory finishing process on the Scout engines varies more than anticipated. While the black-coated surface is consistently present, the bare metal accents are manually ground down at the factory, and the level of grinding differs significantly from bike to bike. This results in variations in width, length, and positioning that I hadn’t encountered in other motorcycle models using the same accent kit design.
When I originally created the template, I used an in-shop Scout engine as the reference, but because of the inconsistent factory finishing, some customers are experiencing partial exposure of the bare metal accents beyond the kit’s coverage area. Additionally, the left-side horizontal accents on many Scouts are shorter than the right side by approximately 12-14mm, which required a unique two-piece installation approach. While that adjustment worked in many cases, the additional issue of varying grinding depths has made it impossible to ensure a consistent, proper fit for all bikes.
Because of this, I’ve made the difficult decision to discontinue this product for the Scout lineup to avoid further frustration. Some customers get a perfect fit. Others may find that some of the bare metal is still visible.

_________

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

CLEARANCE SALE - We are clearing out our old stock of retired designs and other non-current products at an extremely reduced price!

This listing is for 1 set of saddlebag decals. These were tank decals that misprinted too large, making them perfect for saddlebags. See photos for details.

“Hoist the Black Flag" Universal Tank Decals for all Brands and Models of Motorcycles

"Every normal man must be tempted, at times, to spit on his hands, hoist the black flag, and begin slitting throats." - H. L. Mencken

These decals were designed to fit nearly any brand or model of bike.

We recommend checking the measurements to ensure a good fit.

Size: 5.83 inches x 13.26 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

CLEARANCE SALE - We are clearing out our old stock of retired designs and other non-current products at an extremely reduced price!

There's only 1 of these available. This design was originally a custom color order and this second set has remained in our stock until now (since the original customer has moved on to another design).

The Aztec Jaguar God of the Underworld is featured on our Azteca fuel tank decals!  They were designed to fit stylishly on the side of the Indian Scout’s fuel tank and give you a large and unique piece of art to really set your bike apart from the others. 

Size: Approximately 15 x 5 inches (NOT large enough to cover the Challenger's logo or the Scout Twenty full tank side graphic).  The size and shape of this decal is designed to fit the side of the Scout fuel tank.  It has been used on other bikes (see photos), but does not completely cover OEM warbonnet.

Fits: 

• Scout (Scout 86 from 1993-94, Scout from 2001-2002, Scout from 2014-Present (all models except the Bobber Twenty).  See photos for example of the fit

Photo courtesy of Taro Seo

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Gloss pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4.5 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

If not in stock at time of order, may take approximately 2-3 weeks before shipping

“Dragon Slayer” Frame Inserts

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Part of our new lineup of Designer Series decals that take a step away from our traditional themes to bring you more options.

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!

Order both for a complete look!

New Item - Special Order (may take up to two weeks before shipping)

“Dragon Slayer” 

Part of our new lineup of Designer Series decals that take a step away from our traditional themes to bring you more options.

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!

Order both for a complete look!

New Item - Special Order (may take up to two weeks before shipping)

“Dragon Warrior” Frame Inserts

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!

New Item - Special Order (may take up to two weeks before shipping)

“Dragon Warrior” Frame Inserts

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!

New Item - Special Order (may take up to two weeks before shipping)

“Dragon Warrior” 

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!