Products

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 20% off both v-covers

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Usually in stock. (If not in stock at the time of order, may take 2-3 weeks before shipping)

“NEW Skull Warbonnet (B&W)” 

Size: Covers the tank side of 2014-2024 Indian Scout models. If you have a Bobber Twenty or a model that has a pinstripe around the border of the tank, there's always a possibility that a small part of this might show around the edge of the decal. Vinyl expands and contracts slightly depending on temperature.

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Usually in stock. (If not in stock at the time of order, may take 2-3 weeks before shipping)

“NEW Skull Warbonnet (Color)” 

Size: Covers the tank side of 2014-2024 Indian Scout models. If you have a Bobber Twenty or a model that has a pinstripe around the border of the tank, there's always a possibility that a small part of this might show around the edge of the decal. Vinyl expands and contracts slightly depending on temperature.

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

New Item - Special Order (may take up to two weeks before shipping)

“NEW Skull Warbonnet for Thunderstroke Models(Black and White Version)” 

Size: Large decal that covers Original logos on the tank. 

15.35 in x 6.86 in

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

New Item - Special Order (may take up to two weeks before shipping)

“NEW Skull Warbonnet for Thunderstroke Models (Color Version)” 

Size: Large decal that covers Original logos on the tank.

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank.