Our speaker accent vinyl is sold as a kit that accents two speakers.  If you want to accent a pair of saddlebag lid speakers in addition to your fairing speakers, you'll need two kits. Most of our speaker accent vinyl is Oracle 651. Some other brands may be used for harder to find colors. Essentially, it's just single-ply permanent style vinyl that will last a good while if you install it correctly as per instructions below.

To ensure this product fits your bike, please make sure your speakers look like this:  It doesn't matter what model your bike is as long as the speakers have the W shape at the top and a ring around the border.

Installation Instructions:

Installation is peel and stick. The vinyl sheet we send you has all the parts to accent two speakers. Peel and stick one piece at a time and use the back of your fingernail or some other tougher surface to press the vinyl firmly into the textured surface of the speaker.

Screw holes are not pre-cut so that it is easier for you to align and stick on the long circular piece of vinyl. If they were pre-cut, you'd have to get the alignment perfect. Once it's installed, just use one of the screws you removed to carefully poke a hole through the vinyl. It's easy to do since there's literally a hole for the screw in the speaker. When tightening the screws back down, be careful not to overtighten them to the point that the vinyl starts to twist. To avoid this, go slowly and if you see the vinyl start to twist, back the screw off a half turn.

New Item - Special Order (may take up to two weeks before shipping)

“Air Force” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“American Flag (B&W)” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“American Flag (Color)” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Army” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“Arrowhead” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

Ahoy ye swashbucklers and seadogs! We've got some shiny new booty for ye!

Black Bethany here be ready to help you hoist the black flag and get you sailing in the right direction.  This pin-up set is perfect for adding a special touch to your ride.  Keep the rubber side down, and let's try not to feed the fish.

Size: Two sizes are available: 7 x 7.1 inches or 4.5 x 4.6 inches

PRINTABLE SIZE TEMPLATE: Click the cutout template above to download a printable PDF.  You can print this PDF (be sure you have it set to print "actual size") and cut it out to test the size where you want to install these decals.

Fits: 

Anywhere you want to put it.  You can put these on fairings, tanks, saddlebags, cars, trucks,... anywhere.  Just check to make sure it fits where you're sticking it.

New Item - Special Order (may take up to two weeks before shipping)

“Black Wolf” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Brown Wolf” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Chief Iron Shell” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Chief Iron Shell” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your bike.

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“CWB-100” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“CWB-96” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

New Item - Special Order (may take up to two weeks before shipping)

“Coast Guard” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Dark Horse” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Gloss pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4.5 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

If not in stock at time of order, may take approximately 2-3 weeks before shipping

“Dragon Slayer” Frame Inserts

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Part of our new lineup of Designer Series decals that take a step away from our traditional themes to bring you more options.

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!

Order both for a complete look!

New Item - Special Order (may take up to two weeks before shipping)

“Dragon Warrior” Frame Inserts

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!

New Item - Special Order (may take up to two weeks before shipping)

“Dragon Warrior” Frame Inserts

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Dreamcatcher DC420” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 3.7 x 5 inches

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Dreamcatcher DC420” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 3.7 x 5 inches

Gloss Finish pictured above

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: Most options are in-stock and ship immediately.  IF you choose a style that we don’t have in stock, it may take a couple weeks to receive it from our manufacturer before we can ship to you.

These feather accent decals are a set of two for placement on both sides of your bike.  We've designed them in a variety of colors and styles to match our tank and saddlebag decals and offer you more customization options.

Size: Length = 8 inches | Width = 2.25 inches (each)

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a gloss or sandy matte texture.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals. Application suitable for Motorcycles, cars, trucks, windows, tables and more. 

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

Stock Notice: Most options are in-stock and ship immediately.  IF you choose a style that we don’t have in stock, it may take a couple weeks to receive it from our manufacturer before we can ship to you.

These small feather accent decals are a set of two for placement on both sides of your helmet.  Of course, you can put them on anything you like if you don't want them for your helmet.  They will work great for tumblers, tool boxes, or small parts of your bike.  We've designed them in a variety of colors and styles to match our tank and saddlebag decals and offer you more customization options.

Size: Length = 5.1 inches | Width = 1.4 inches (each)

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a gloss or sandy matte texture.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals. Application suitable for Motorcycles, cars, trucks, windows, tables and more. 

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“FWB-119” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

Usually in-stock (if out of stock, could take approximately two weeks before shipping)

“FWB-123” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“FWB-18167678” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Huntress” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Gloss finish pictured above

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your bike.

Usually in stock (if out of stock, may take up to two weeks before shipping)

“Huntress” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Gloss Finish

Matte Finish

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

'Bronze' is not a metallic finish. This is a printed DTF material as described below.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.