Products

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 20% off both v-covers

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“CWB-100” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“CWB-96” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4 weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4 weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4 weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4 weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4 weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4 weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4 weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4 weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.