Products

Special Order Item (may not always be in stock and could take approximately two weeks before shipping) 

American Flag Decal Set for new style Indian Saddlebags

Size: Fits the side of the left and right saddlebag for the newer style (non-rounded) Indian hard bags.  For models that have the plastic bag guard on the front/bottom corner, the guard must be removed to use these decals. (See Mock-up images)

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order Item (may not always be in stock and could take approximately two weeks before shipping) 

American Flag Decal Set for new style Indian Saddlebags

Size: Fits the side of the left and right saddlebag for the newer style (non-rounded) Indian hard bags.  For models that have the plastic bag guard on the front/bottom corner, the guard must be removed to use these decals. (See Mock-up images)

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Product is made to order: usually takes approximately 2 weeks for us to receive them from our manufacturer before shipping to you.

The first design in our new BWC Racing lineup of bagger-racing inspired livery for your Indian Challenger/Pursuit. "Podium Finish" features a checkered flag as a tribute to our winning performance on the track. This decal set is available in gloss or matte finish and includes fairing, tank, and saddlebag graphics with two additional BWC Racing decals. Install them all or just the ones you want, every set contains a total of 8 decals.

Installation:

Decal installation should be done using the wet method as explained in our "How-to" video.

Decal Placement:

The Fairing decals are meant to align with the front cutout section where the lights are and the back end matches up with the downward curve on fairing.

Mock Up: (gold/carbon shown here)

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

SPECIAL ORDER - these decals may take approximately two weeks before shipping due to manufacturing times

Give your motorcycle a custom look with these Dark Horse saddlebag decals!  They are designed for both versions of Indian saddlebags, the common style, and the newer style.  Although they were designed for the saddlebags, you can use these decals wherever you want.  Just be sure to measure the size of where you want to apply them to ensure they will fit.

Size: 

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl and laminated with a 12-mil glossy PVC laminate or with a sandy matte texture (your choice).  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

What is included:  Matching set of left and right facing decals. Application suitable for Motorcycles, cars, trucks, windows, tables and more. 

Installation: We recommend using the wet method to install decals of this size.  Take a look at this video made by TAB Performance during their installation of our decals.

Give your motorcycle a custom look with these Dark Horse saddlebag decals!  They are designed for both versions of Indian saddlebags, the common style, and the newer style.  Although they were designed for the saddlebags, you can use these decals wherever you want.  Just be sure to measure the size of where you want to apply them to ensure they will fit.

Size: 

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl and laminated with a 12-mil glossy PVC laminate or with a sandy matte texture (your choice).  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

What is included:  Matching set of left and right facing decals. Application suitable for Motorcycles, cars, trucks, windows, tables and more. 

Installation: We recommend using the wet method to install decals of this size.  Take a look at this video made by TAB Performance during their installation of our decals.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

Product is made to order: usually takes approximately 2 weeks for us to receive them from our manufacturer before shipping to you.

The first design in our new BWC Racing lineup of bagger-racing inspired livery for your Indian Challenger/Pursuit. "Podium Finish" features a checkered flag as a tribute to our winning performance on the track. This decal set is available in gloss or matte finish and includes fairing, tank, and saddlebag graphics with two additional BWC Racing decals. Install them all or just the ones you want, every set contains a total of 8 decals.

Installation:

Decal installation should be done using the wet method as explained in our "How-to" video.

View this post on Instagram

A post shared by Mike Ferraiolo (@ferraiolo_1)

Decal Placement:

The Fairing decals are meant to align with the front cutout section where the lights are and the back end matches up with the downward curve on fairing.

Product is made to order: usually takes approximately 2 weeks for us to receive them from our manufacturer before shipping to you.

The first design in our new BWC Racing lineup of bagger-racing inspired livery for your Indian Challenger/Pursuit. "Podium Finish" features a checkered flag as a tribute to our winning performance on the track. This decal set is available in gloss or matte finish and includes fairing, tank, and saddlebag graphics with two additional BWC Racing decals. Install them all or just the ones you want, every set contains a total of 8 decals.

Installation:

Decal installation should be done using the wet method as explained in our "How-to" video.

Decal Placement:

The Fairing decals are meant to align with the front cutout section where the lights are and the back end matches up with the downward curve on fairing.

Mockup placement: (Gold/carbon shown here)

New Item - Special Order (may take up to two weeks before shipping)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

New Item - Special Order (may take up to two weeks before shipping)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

New Item - Special Order (may take up to two weeks before shipping)

“MMIW Red Hand” Anywhere Decal - A Charity Drive Project

Missing and Murdered Indigenous Women is an epidemic of violence against Indigenous women in Canada, the United States, and Latin America; notably those in the FNIM and Native American communities. Across Latin America, it is estimated that Indigenous women and girls are disproportionately the victims of femicide.

STATISTICS

• Indigenous Women (girls +) murdered 10x higher than all other ethnicities.
• Murder is the 3rd leading cause of death for Indigenous Women (Centers for Disease Control).
• More than 4 out of 5 Indigenous Women have experienced violence (84.3%) (National Institute of Justice Report).
• More than half Indigenous Women experience sexual violence (56.1%).
• More than half Indigenous Women have been physically abused by their intimate partners (55.5 percent).
• 48.8% of Indigenous Women have been stalked in their lifetime.
• Indigenous Women are 1.7 times more likely than Anglo-American women to experience violence.
• Indigenous Women are 2xs more likely to be raped than Anglo-American white women.
• Murder rate of Indigenous Women is 3xs higher than Anglo-American women.

These decals are meant to bring awareness to this issue and can be used anywhere. Brave Wolf Customs will donate $15 from each order to a non-profit charitable organization whose mission is to offer support to the MMIW demographic.

Size: 7.5 x 7.2 inches each when displayed in the orientation of the image below

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take approximately 2-3 weeks before shipping if not in stock at time of order)

"Ragnarok" depicts Fenrir facing off against Jörmungandr the World Serpent during the apocalyptical events of the Twilight of the Gods.

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take approximately 2-3 weeks before shipping if not in stock at time of order)

"Ragnarok" depicts Fenrir facing off against Jörmungandr the World Serpent during the apocalyptical events of the Twilight of the Gods.

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

Product is made to order: usually takes approximately 2 weeks for us to receive them from our manufacturer before shipping to you.

The first design in our new BWC Racing lineup of bagger-racing inspired livery for your Indian Challenger/Pursuit. "Podium Finish" features a checkered flag as a tribute to our winning performance on the track. This decal set is available in gloss or matte finish and includes fairing, tank, and saddlebag graphics with two additional BWC Racing decals. Install them all or just the ones you want, every set contains a total of 8 decals.

Installation:

Decal installation should be done using the wet method as explained in our "How-to" video.

Decal Placement:

The Fairing decals are meant to align with the front cutout section where the lights are and the back end matches up with the downward curve on fairing.

Mock Up: (gold/carbon shown here)

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

New Item - Special Order (may take 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

New Item - Special Order (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

New Item - Special Order (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

The Zombie Baffles from TAB Performance are on another level and really deserved their own artwork.  We designed these two color variations for our own Challenger and for TAB Performance but we want to make them available to anyone else who’d like to have them.

They are special order from our manufacturer so they require up to 2 weeks lead time before delivery.  On occasion, we may have a set in stock that can ship right away.

Fitment: 2020 Indian Challenger and newer (with saddlebag guards still on the bags)

These decals can be purchased in HD Gloss or Sandy Matte finishes and we have both a “red” version and a “white”.

Self-adhesive, weatherproof outdoor vinyl will last for many years and will not damage paint finishes if they are removed.

We recommend using the wet method to install these decals with a squeegee/plastic putty-knife/or credit card.  

Photo: Greg LeBlanc / Model: Violetta Nunez

Get your TAB Performance B.A.M. Sticks exhaust and Zombie Baffles if you haven’t already bought them!

The Zombie Baffles from TAB Performance are on another level and really deserved their own artwork.  We designed these two color variations for our own Challenger and for TAB Performance but we want to make them available to anyone else who’d like to have them.

They are special order from our manufacturer so they require up to 2 weeks lead time before delivery.  On occasion, we may have a set in stock that can ship right away.

Fitment: 2020 Indian Challenger and newer (with saddlebag guards still on the bags)

These decals can be purchased in HD Gloss or Sandy Matte finishes and we have both a “red” version and a “white”.

Self-adhesive, weatherproof outdoor vinyl will last for many years and will not damage paint finishes if they are removed.

We recommend using the wet method to install these decals with a squeegee/plastic putty-knife/or credit card.  

Get your TAB Performance B.A.M. Sticks exhaust and Zombie Baffles if you haven’t already bought them!

New Item - Special Order (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.