Products

Stock Notice: Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“MMIW Red Hand” Anywhere Decal - A Charity Drive Project

Missing and Murdered Indigenous Women is an epidemic of violence against Indigenous women in Canada, the United States, and Latin America; notably those in the FNIM and Native American communities. Across Latin America, it is estimated that Indigenous women and girls are disproportionately the victims of femicide.

STATISTICS

• Indigenous Women (girls +) murdered 10x higher than all other ethnicities.
• Murder is the 3rd leading cause of death for Indigenous Women (Centers for Disease Control).
• More than 4 out of 5 Indigenous Women have experienced violence (84.3%) (National Institute of Justice Report).
• More than half Indigenous Women experience sexual violence (56.1%).
• More than half Indigenous Women have been physically abused by their intimate partners (55.5 percent).
• 48.8% of Indigenous Women have been stalked in their lifetime.
• Indigenous Women are 1.7 times more likely than Anglo-American women to experience violence.
• Indigenous Women are 2xs more likely to be raped than Anglo-American white women.
• Murder rate of Indigenous Women is 3xs higher than Anglo-American women.

These decals are meant to bring awareness to this issue and can be used anywhere. Brave Wolf Customs will donate $15 from each order to a non-profit charitable organization whose mission is to offer support to the MMIW demographic.

Size: 7.5 x 7.2 inches each when displayed in the orientation of the image below

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, or if your model has embossed letters on the v-cover, you can fill those in with silicon or putty or cover it with some vinyl or tape before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, or if your model has embossed letters on the v-cover, you can fill those in with silicon or putty or cover it with some vinyl or tape before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This is the NEW Version 2 of our Black & White Mayan Calendar

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video: