Stock Notice: (may take approximately two - three weeks before shipping if not in stock at time of your order)

“Fenrir" Universal Tank Decals for all Brands and Models of Motorcycles

This design was custom commissioned and our client has graciously allowed us to share it with other customers.

Size: 15.26 x 5.85 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank.

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock but may take 2-3 weeks before shipping if not in stock at the time of your order.

“Fenrir" Full-Tank Decal for Indian Scout models

This design was custom commissioned and our client has graciously allowed us to share it with other customers.

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order Items sometimes need to be manufactured after you order if we don't currently have a set in stock (could take approximately two weeks before shipping)

“Herald of Dawn” 

Size: Covers the full tank side of Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

New Item - Special Order (may take up to two weeks before shipping)

“Herald of Dawn” 

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.  See customer photos attached for reference.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Hoist the Black Flag" Universal Tank Decals for all Brands and Models of Motorcycles

"Every normal man must be tempted, at times, to spit on his hands, hoist the black flag, and begin slitting throats." - H. L. Mencken

These decals were designed to fit nearly any brand or model of bike.

We recommend checking the measurements to ensure a good fit.

Size: 5.83 inches x 13.26 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice:  (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Hoist the Black Flag" Universal Tank Decals for all Brands and Models of Motorcycles

"Every normal man must be tempted, at times, to spit on his hands, hoist the black flag, and begin slitting throats." - H. L. Mencken

These decals were designed to fit nearly any brand or model of bike.

We recommend checking the measurements to ensure a good fit.

Size: 5.83 inches x 13.26 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Honeycomb Sunset” 

Part of our new lineup of Designer Series decals that take a step away from our traditional themes to bring you more options.

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

'Bronze' is not a metallic finish. This is a printed DTF material as described below.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

'GOLD' accents are not metallic. This is a printed DTF material with a semi-gloss finish.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

'Gun Metal' is not metallic. This is a printed DTF material as described below.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

SPECIAL-ORDER

Usually in stock. If not in stock at time of order, there can be a lead time before shipping.

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

MADE TO ORDER: I make these in-house in the order that orders are received. It is a time-consuming process and a limited number can be made each day. Please be patient and wait until your order is ready before I can ship it.

After being unavailable for nearly a full year, we're happy to announce that we have received our new state of the art machinery and these are back in production.

Chief Warbonnet

The Chief Warbonnet is our second 3D sculpted design. The likeness is based on historical photos to make it an accurate representation.  For this design, I wanted it to look similar to a fossil.  In that way, it can have the appearance of being excavated or it can look like it’s carved from rock.  This emblem will fit perfectly into the embossed area of the Indian Scout mid-frame just below the seat and can be installed with 3M emblem tape or with a pliable silicone adhesive (your choice). 

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A durable resin, painted charcoal black to match the Scout frame.  Can be painted on if you design to custom paint it yourself.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.

What is included:  Set of Left and Right side or Right side mid-frame emblem insert (depending on which option is ordered) and 3M emblem tape

How to Install: Method 1:  Clean the mid-frame area of the bike of dirt and debris before installation.  We recommend using a alcohol swab.  Peel and stick 3M emblem tape on the reverse side of the emblem.  Press into place on bike frame and hold firmly in place for 30 seconds or more.  Allow tape adhesive to cure for 1-3 hours before riding to ensure a strong bond. 

MADE TO ORDER: I make these in-house in the order that orders are received. It is a time-consuming process and a limited number can be made each day. Please be patient and wait until your order is ready before I can ship it.

After being unavailable for nearly a full year, we're happy to announce that we have received our new state of the art machinery and these are back in production.

Nizhoni Warbonnet

The Nizhoni Warbonnet is our third 3D sculpted design. I wanted to create a sculpt that could be a companion piece to the Nizhoni decal artwork I’ve done and I really appreciate enjoyed sculpting the flowing hair.  For this design, I wanted it to look similar to a fossil.  In that way, it can have the appearance of being excavated or it can look like it’s carved from rock.  This emblem will fit perfectly into the embossed area of the Indian Scout mid-frame just below the seat and can be installed with 3M emblem tape or with a pliable silicone adhesive (your choice). 

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A durable resin, painted charcoal black to match the Scout frame.  Can be painted on if you design to custom paint it yourself.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.

What is included:  Set of Left and Right side or Right side mid-frame emblem insert (depending on which option is ordered) and 3M emblem tape

How to Install: Method 1:  Clean the mid-frame area of the bike of dirt and debris before installation.  We recommend using a alcohol swab.  Peel and stick 3M emblem tape on the reverse side of the emblem.  Press into place on bike frame and hold firmly in place for 30 seconds or more.  Allow tape adhesive to cure for 1-3 hours before riding to ensure a strong bond. 

MADE TO ORDER: I make these in-house in the order that orders are received. It is a time-consuming process and a limited number can be made each day. Please be patient and wait until your order is ready before I can ship it.

After being unavailable for nearly a full year, we're happy to announce that we have received our new state of the art machinery and these are back in production.

Skull Warbonnet

The skull warbonnet is our first 3D sculpted design because we’ve never received more requests for any other design.  There’s just something powerful about it that seems to connect with so many people.  For this design, I wanted it to look similar to a fossil.  In that way, it can have the appearance of being excavated or it can look like it’s carved from rock.  This emblem will fit perfectly into the embossed area of the Indian Scout mid-frame just below the seat and can be installed with 3M emblem tape or with a pliable silicone adhesive (your choice). 

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A durable resin, painted charcoal black to match the Scout frame.  Can be painted on if you design to custom paint it yourself.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.

What is included:  Set of Left and Right side or Right side mid-frame emblem insert (depending on which option is ordered) and 3M emblem tape

How to Install: Method 1:  Clean the mid-frame area of the bike of dirt and debris before installation.  We recommend using a alcohol swab.  Peel and stick 3M emblem tape on the reverse side of the emblem.  Press into place on bike frame and hold firmly in place for 30 seconds or more.  Allow tape adhesive to cure for 1-3 hours before riding to ensure a strong bond. 

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

Stock Notice: Usually in stock (may take approximately 2-3 weeks before shipping if not in stock)

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

Brand New Item

Must be Manufactured before shipping

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  We now manufacture these with a sandy matte finish to match the frame (rather than the gloss you'll see in some photos).  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

View this post on Instagram

A post shared by 🖤indian.smoke🖤 (@indian.smoke)

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

Special Order Item - We may carry a small inventory but expect a possible wait time of about 2 weeks if we need to order from our manufacturer.

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Photo courtesy of Terry Scott

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

(may take approximately two weeks before shipping if not in stock at time of order)

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods