Our speaker accent vinyl is sold as a kit that accents two speakers.  If you want to accent a pair of saddlebag lid speakers in addition to your fairing speakers, you'll need two kits. Most of our speaker accent vinyl is Oracle 651. Some other brands may be used for harder to find colors. Essentially, it's just single-ply permanent style vinyl that will last a good while if you install it correctly as per instructions below.

To ensure this product fits your bike, please make sure your speakers look like this:  It doesn't matter what model your bike is as long as the speakers have the W shape at the top and a ring around the border.

Installation Instructions:

Installation is peel and stick. The vinyl sheet we send you has all the parts to accent two speakers. Peel and stick one piece at a time and use the back of your fingernail or some other tougher surface to press the vinyl firmly into the textured surface of the speaker.

Screw holes are not pre-cut so that it is easier for you to align and stick on the long circular piece of vinyl. If they were pre-cut, you'd have to get the alignment perfect. Once it's installed, just use one of the screws you removed to carefully poke a hole through the vinyl. It's easy to do since there's literally a hole for the screw in the speaker. When tightening the screws back down, be careful not to overtighten them to the point that the vinyl starts to twist. To avoid this, go slowly and if you see the vinyl start to twist, back the screw off a half turn.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, or if your model has embossed letters on the v-cover, you can fill those in with silicon or putty or cover it with some vinyl or tape before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, or if your model has embossed letters on the v-cover, you can fill those in with silicon or putty or cover it with some vinyl or tape before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

If not in stock at the time of your order, it could take approximately 2-3 weeks before we can ship out.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, or if your model has embossed letters on the v-cover, you can fill those in with silicon or putty or cover it with some vinyl or tape before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This is the NEW Version 2 of our Black & White Mayan Calendar

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video: