Indian Challenger & Pursuit

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Embers 2-2023" Universal Tank Decals for all Brands and Models of Motorcycles

Strikingly different yet familiarly shaped like a headdress, Embers invokes ancient sorcery and is styled with the look of fire magic and shadow.

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

If you have an Indian Scout, we recommend purchasing our Scout version which is slightly smaller in order fit on the tank side without extending over the border.

Size: 6.44 inches x 14.74 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Gloss pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Wolf Paw Print Accent Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4 paw prints at 2" in height. 5 paw prints at 1.5" in height

These decals are a direct-to-film DTF graphic kit that comes with a transfer layer on top that makes it easy to apply them. They are all black with no background color and have an enamel-like finish.

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Druid Chief Warbonnet" Universal Tank Decals for all Brands and Models of Motorcycles

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, check the dimensions above.

How To Install: <-Visit our How To page for videos

Our heavy-duty laminated weatherproof vinyl decals are hi-tac self-adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Dreamcatcher Female Warbonnet" Universal Tank Decals for all Brands and Models of Motorcycles

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

Size: 5.75 inches x 14.83 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, check the dimensions above.

How To Install: <-Visit our How To page for videos

Our heavy-duty laminated weatherproof vinyl decals are hi-tac self-adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Dreamcatcher Chief Warbonnet" Universal Tank Decals for all Brands and Models of Motorcycles

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

Size: 5.75 inches x 14.9 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, check the dimensions above.

How To Install: <-Visit our How To page for videos

Our heavy-duty laminated weatherproof vinyl decals are hi-tac self-adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

CLEARANCE SALE - We are clearing out our old stock of retired designs and other non-current products at an extremely reduced price.!

We are retiring many of our designs, making them limited in nature.  We want this process to help make your bike unique.  If you've been thinking about scoring a set of these custom decals, get them now before they're gone!

Native American cultures appreciated all aspects of nature, and while animal mysticism was subject to tribal and individualistic interpretations, the wolf has been known to represent intelligence, teacher, organizer, hunter, and loyalty.

Size: 14.47 inches length by 5.9 inches tall (Indian Scout owners should purchase the Scout version of this art.  It is a different product)

Photo courtesy of Justin Ballou

CLEARANCE SALE - We are clearing out our old stock of retired designs and other non-current products at an extremely reduced price!

Limited quantity remaining before they're gone forever!

Native American cultures appreciated all aspects of nature, and while animal mysticism was subject to tribal and individualistic interpretations, the wolf has been known to represent intelligence, teacher, organizer, hunter, and loyalty.

Size: 14.47 inches length by 5.9 inches tall (Indian Scout owners should purchase the Scout version of this art.  It is a different product)

Photo courtesy of Timothy Domeier

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Alchemy 1-2023" Universal Tank Decals for all Brands and Models of Motorcycles

There's a potion, a fix for that ailment you have. A cure for your boredom, a tincture to revive your spirit after a long week of work. It's called "riding a motorcycle". And that's what "Alchemy" represents.

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

If you have an Indian Scout, we recommend purchasing our Scout version which is slightly smaller in order fit on the tank side without extending over the border.

Size: 6.15 inches x 14.9 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Jaymus Thunderbird" Universal Tank Decals for all Brands and Models of Motorcycles

This powerful Indian Chief was made in the likeness of my friend Jaymus Perry, a Native American Navajo artist, the creator of Art Bonnet.

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

If you have an Indian Scout, we recommend purchasing our Scout version which is slightly smaller in order fit on the tank side without extending over the border.

Size: 6.1 inches x 14.4 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4.5 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Tank Decal set for Indian Challenger/Pursuit, Powerplus Chieftain, Powerplus Roadmaster

Size: Covers a large portion of the tank side and should be centered during application for greatest appeal.

This design was custom commissioned and our client has graciously allowed us to share it with other customers.

Size: Covers a large portion of the tank side on Challenger and Pursuit models and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Tank Decal set for Indian Challenger/Pursuit, Powerplus Chieftain, Powerplus Roadmaster

Size: Covers a large portion of the tank side and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Fits Indian Challenger and Pursuit, Powerplus Chieftain, and Powerplus Roadmaster

Size: Covers a large portion of the tank side and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Dreamcatcher Female Warbonnet" Universal Tank Decals for all Brands and Models of Motorcycles

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

Size: 5.75 inches x 14.83 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, check the dimensions above.

How To Install: <-Visit our How To page for videos

Our heavy-duty laminated weatherproof vinyl decals are hi-tac self-adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: usually takes approximately 2+ weeks for us to receive them from our manufacturer before shipping to you if they're not in stock at the time of your order.

The first design in our new BWC Racing lineup of bagger-racing inspired livery for your Indian Challenger/Pursuit. "Podium Finish" features a checkered flag as a tribute to our winning performance on the track. This decal set is available in gloss or matte finish and includes fairing, tank, and saddlebag graphics with two additional BWC Racing decals. Install them all or just the ones you want, every set contains a total of 8 decals.

Installation:

Decal installation should be done using the wet method as explained in our "How-to" video.

Decal Placement:

The Fairing decals are meant to align with the front cutout section where the lights are and the back end matches up with the downward curve on fairing.

Mock Up: (gold/carbon shown here)

Stock Notice:  (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Hoist the Black Flag" Universal Tank Decals for all Brands and Models of Motorcycles

"Every normal man must be tempted, at times, to spit on his hands, hoist the black flag, and begin slitting throats." - H. L. Mencken

These decals were designed to fit nearly any brand or model of bike.

We recommend checking the measurements to ensure a good fit.

Size: 5.83 inches x 13.26 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Alchemy 1-2023" Universal Tank Decals for all Brands and Models of Motorcycles

There's a potion, a fix for that ailment you have. A cure for your boredom, a tincture to revive your spirit after a long week of work. It's called "riding a motorcycle". And that's what "Alchemy" represents.

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

If you have an Indian Scout, we recommend purchasing our Scout version which is slightly smaller in order fit on the tank side without extending over the border.

Size: 6.15 inches x 14.9 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Embers 2-2023" Universal Tank Decals for all Brands and Models of Motorcycles

Strikingly different yet familiarly shaped like a headdress, Embers invokes ancient sorcery and is styled with the look of fire magic and shadow.

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

If you have an Indian Scout, we recommend purchasing our Scout version which is slightly smaller in order fit on the tank side without extending over the border.

Size: 6.44 inches x 14.74 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Jaymus Thunderbird" Universal Tank Decals for all Brands and Models of Motorcycles

This powerful Indian Chief was made in the likeness of my friend Jaymus Perry, a Native American Navajo artist, the creator of Art Bonnet.

These decals were designed to cover the original headdress on Indian Motorcycles but can be used by any brand or model of bike.

If you have an Indian Scout, we recommend purchasing our Scout version which is slightly smaller in order fit on the tank side without extending over the border.

Size: 6.1 inches x 14.4 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video TAB Performance made while installing our Zombie decals.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Special Edition Lilith" Tank Decal set

Unleash the dark allure of Lilith, the mother of demons and co-creator of Sanctuary, right on your motorcycle's tank! Originally created for our own custom bike build, the Lilith Challenger, we're thrilled to make this captivating artwork available to fellow Powerplus 108 enthusiasts like you.

Inspired by the enigmatic character from Blizzard's renowned Diablo franchise, our Special Edition Lilith Tank Decals exude an irresistible mystique that is sure to turn heads wherever you ride.

Designed in a striking tank-side panel style, these decals cover a substantial portion of the tank, making a bold statement that demands attention. They are meticulously crafted to be large enough to effortlessly conceal OEM style headdress logos, allowing you to completely transform the look of your motorcycle.

They can be applied directly over existing graphics, making installation a breeze. No need to remove or modify your bike's current design. Simply adhere the decal over it, and watch as your motorcycle undergoes a remarkable transformation.

Crafted with meticulous attention to detail, our decals are made from high-quality materials, ensuring longevity and durability. They are built to withstand the rigors of the road, keeping your bike looking stunning for years to come.

Please note: These decals are specifically designed for Indian Challenger and Pursuit models. Ensure compatibility before making your purchase.

Embrace the darkness, embrace the allure of Lilith!

Size: Covers a large portion of the tank side on Challenger and Pursuit models and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Blue" SWB-729 Tank Decal for Indian Challenger and Pursuit

Size: Covers a large portion of the tank side on Challenger and Pursuit models and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Viking 001” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 3.8 x 5 inches each (Set of left and right facing decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Military Pin-up 869” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4.4 x 5 inches

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video: