Indian Challenger & Pursuit

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 20% off both v-covers

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, or if your model has embossed letters on the v-cover, you can fill those in with silicon or putty or cover it with some vinyl or tape before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

New Item - Special Order (may take approximately two weeks before shipping)

“Fenrir" Universal Tank Decals for all Brands and Models of Motorcycles

This design was custom commissioned and our client has graciously allowed us to share it with other customers.

Size: 15.26 x 5.85 inches

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank.

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Fenrir" Tank Decal set for Indian Challenger/Pursuit

This design was custom commissioned and our client has graciously allowed us to share it with other customers.

Size: Covers a large portion of the tank side on Challenger and Pursuit models and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Ragnarok" Tank Decal set for Indian Challenger/Pursuit

Size: Covers a large portion of the tank side on Challenger and Pursuit models and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Ragnarok" Tank Decal set for Indian Challenger/Pursuit

Size: Covers a large portion of the tank side on Challenger and Pursuit models and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.