Indian Motorcycle

Special Order (may take approximately 3-4 weeks before shipping if not in stock at the time of your order)

“Chief Warbonnet CWB-729" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers a large portion of the tank side with a small area in front of the face for the original paint to show.  If you have a model with a tank graphic that is really close to the edges of the tank, a small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 3-4 weeks before shipping if not in stock at the time of your order)

“Chief Warbonnet CWB-729" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers a large portion of the tank side with a small area in front of the face for the original paint to show.  If you have a model with a tank graphic that is really close to the edges of the tank, a small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 3-4 weeks before shipping if not in stock at the time of your order)

“Chief Warbonnet CWB-729" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers a large portion of the tank side with a small area in front of the face for the original paint to show.  If you have a model with a tank graphic that is really close to the edges of the tank, a small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Stock Notice: (may take approximately 3-4 weeks before shipping if not in stock at time of order)

Tank Decal set for Indian Challenger/Pursuit, Powerplus Chieftain, Powerplus Roadmaster

Our new CWB-729 Chief Warbonnet decals were created in the same style as our best-selling SWB-729 Skull Warbonnet decals. We created them to fill the gap for those riders who aren't into skulls and are looking for the more traditional approach.

Size: Covers a large portion of the tank side and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

SPECIAL ORDER - these decals may take approximately two weeks before shipping due to manufacturing times

Give your motorcycle a custom look with these Dark Horse saddlebag decals!  They are designed for both versions of Indian saddlebags, the common style, and the newer style.  Although they were designed for the saddlebags, you can use these decals wherever you want.  Just be sure to measure the size of where you want to apply them to ensure they will fit.

Size: 

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl and laminated with a 12-mil glossy PVC laminate or with a sandy matte texture (your choice).  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

What is included:  Matching set of left and right facing decals. Application suitable for Motorcycles, cars, trucks, windows, tables and more. 

Installation: We recommend using the wet method to install decals of this size.  Take a look at this video made by TAB Performance during their installation of our decals.

CLEARANCE SALE - We are clearing out our old stock of retired designs and other non-current products at an extremely reduced price!

This listing is for 1 set of tank decals. These were supposed to be blue but printed a dark purple. See photos for details.

“Dark Purple" SWB-729 Tank Decal for Indian Challenger and Pursuit

Size: Covers a large portion of the tank side on Challenger and Pursuit models and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Surtr in Muspelheim" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Special Order (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

“Surtr in Muspelheim" Tank Decal set for Indian Scout (2014-2024 models)

Size: Covers the full tank side of ALL Indian Scout models.  If you have a model with a tank graphic that is really close to the edges of the tank, a very small portion of that graphic may show around the edge of the decal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Tank Decal set for Indian Challenger/Pursuit, Powerplus Chieftain, Powerplus Roadmaster

Size: Covers a large portion of the tank side and should be centered during application for greatest appeal.

Weatherproof laminated decals are self adhesive. 

How To Install: <-Visit our How To page for videos

We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  To get the proper soap/water mix, start with a squirt of soap into your spray bottle.  Shake it up and then spray it on your hand.  Rub your finger tips together.  You should feel the slipperiness of the soap.  If it just feels like water, add more soap and try again.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. A plastic putty scraper with a thin cloth wrapped around it will work great and prevent scratching your decals.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

Stock Notice: (may take approximately 2-3 weeks before shipping if not in stock at the time of your order)

Our saddlebag decals are made from premium weatherproof hi-tack vinyl with a long lifespan that will keep them looking new for years.  They are available in two finishes, heavy-duty 12 mil laminated Gloss (looks like it's painted on), or a heavy-duty sandy matte textured premium finish.

Installation:

Installing our decals is easy to do yourself at home.  We recommend removing all of the excess decal material (the background image) before installing the decals.  This will allow you to dispose of all the small cut-out pieces so that the pieces do not get trapped underneath your decal when installing it on the bike.  Once you have all of the small pieces and background removed, you can use the "wet method" to install the decals to your saddlebags.  The wet method involves using a spray bottle of water with a couple drops of dish soap in the mixture and spraying the surface of your saddlebags to wet the entire surface.  Then carefully remove the backing from your decal and use the spray bottle to wet the adhesive side of the decal.  Now you can gently place the decal on your saddlebag.  Because the surfaces are wet, you can pull the decal up to reposition it until you get it where you want it.  Once it's in place, use a squeegee or other object such as a credit card wrapped in a microfiber towel to squeeze the water out from behind the decal.  You can also use your hands to do this.  You should take care not to use a hard/abrasive object that can scratch the decals or your bike's paint.  The high-tack adhesive will begin to set/adhere to the bike as soon as the liquid is push out from behind the decal.  Use caution to ensure the towel or object you are using does not catch any edges of the decal and pull it off your bike.  If you take your time and be gentle during installation, it should be an easy process.  A hair dryer can be used to speed up the drying process if needed.

Feel free to visit our How-To page on the website to watch a "wet method" installation video.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

Fits Indian Powerplus models without lowers

The Mustache highway bars are perfect for adding that unique style to your bike!

Made from steel with precision for a superior fit.  Powder coated for durability and protection from the elements.

Fits 2014+ Indian Chieftain (and Elite), Springfield, Vintage, Classic, and Roadmaster (without OEM lowers), and their Darkhorse versions

The Meathook highway bars are for the owner who's looking for aggressive styling.  Don't forget to also pick up a set of matching rear highway bars.

Made from steel with precision for a superior fit.  Powder coated for durability and protection from the elements.

Fits 2014+ Indian Chieftain (and Elite), Springfield, Vintage, Classic, and Roadmaster (without OEM lowers), and their Darkhorse versions

The Flat-top highway bars feature strong lines and a sweeping lower curve that compliment the bike's style.

Made from steel with precision for a superior fit.  Powder coated for durability and protection from the elements.

INTERNATIONAL ORDERS - please order directly from www.RydeCulture.com

INTERNATIONAL ORDERS - please order directly from www.RydeCulture.com

INTERNATIONAL ORDERS - please order directly from www.RydeCulture.com

INTERNATIONAL ORDERS - please order directly from www.RydeCulture.com

RydeCulture’s Bryant M1 lights are designed to distinguish your Indian Motorcycle away from the pack in a subtle and classy manner. There’s no reason to go down the road looking like a Christmas tree. These lights accentuate the Indian Motorcycles body lines and follow the curves of the bag. The amber sequential turn signals also give your Indian a unique personal stamp.

INTERNATIONAL ORDERS - please order directly from www.RydeCulture.com

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Special Order Item (may take approximately 2-3 weeks before shipping if we don't have it in stock at the time of your order)

“Horns 2024" decal set for 2022+ Indian Chief side panels.

Set of matching left and right side decals for the side panels.

How To Install: <-Visit our How To page for videos

Our heavy-duty laminated weatherproof vinyl decals are hi-tac self-adhesive.  If your side panels have a smooth gloss or sandy matte finish, we recommend using the wet method to install these decals. If your side panels have a rough matte texture, you should be able to apply them "dry" easily enough by getting them positioned well before pressing down to firmly adhere them.

A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take approximately two+ weeks before shipping)

“TropicalBobber Mermaid" Indian Scout Tank Decals for all models of Indian Scout

Originally designed as a one-of-a-kind custom for our own Sheila, @tropicalbagger on Instagram and formerly known as @tropicalbobber, we're making these decals available to our customers as she now rides a Chieftain Limited.

These decals were designed to fit on the side of the Indian Scout tank (all models).  If your tank has a pre-existing design, we cannot guarantee this decal will cover it.  Please look at the product thumbnail that shows how it fits on the tank side to determine if this decal is for you. At the time of product launch, the Indian Scout "Twenty" models are the only models we know of where the tank pinstripe graphic may extend past the borders of our decal

Size: Full tank side panel

These decals are designed for all brands/models of motorcycles.  Check the measurements to ensure a proper fit on your bike before ordering.  If your tank already has a graphic, we can’t guarantee these decals will cover it completely.  To verify fit and coverage, print out the template below, cut it out and tape it to your tank. (Print out template will be added soon)

How To Install: <-Visit our How To page for videos

Weatherproof HD Gloss finish vinyl decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.

Custom item made-to-order:

If this item isn't in stock when you order it, it could take approximately 4+ weeks for us to make it for you before we can ship. Due to the custom nature of this product, that you can choose different artwork for both sides of your bike, and the fact that we make these by hand in-house, please be patient while waiting for your order.  If you'd like to know which designs we have in-stock and ready to ship before you choose, please contact us.

Premium saddlebag tethers from Brave Wolf Customs are an awesome way to add character to your bike.  These tethers are available with a wide variety of artwork to choose from and are sold as singles with a Left OR Right option so that you can mix and match to pick the artwork you want.

• Waterproof Ottertex fabric
• Premium DTF graphics
• Easy installation requiring no modification to your bike
• Re-uses the Mounting brackets from your OEM tethers (If you are ordering these for aftermarket bags and do not have the mounting brackets from OEM tethers, send us an email and we can print some brackets for you with impact resistant ABS-like resin)
  The mounting brackets in your OEM tethers are held in place with a small bit of glue that will release when you slip a flat tip screwdriver or similar object between the tether and the bracket.

Choose LEFT or RIGHT then add to cart.  Don't forget to choose a design for the other bag as well.