We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Military Pin-up 869” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4.4 x 5 inches

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

ABOUT THIS COLOR: Sunset Red Smoke is not a matte finish since that is impossible with DTF graphics like these accent kits. However, it is a slightly altered version of Sunset Red so that it matches more closely to the "smoke" version of the paint job. This color was sampled directly from the official website color selection.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“SWB-120” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

New Item - Special Order (may take up to two weeks before shipping)

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

(may take approximately two weeks before shipping if not in stock at time of order)

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

(may take approximately two weeks before shipping if not in stock at time of order)

We've all looked at the beautiful frame of the Indian Scout and saw the potential for adding custom graphics or emblems to the embossed / inset areas.  Now we've created these weatherproof heavy-duty laminated vinyl decals to fill those spaces for a unique custom look.  These aren't emblems that require special adhesives or materials.  They are hi-tack vinyl designed with 3 dimensional graphics to have the appearance of emblems but with ease of cleaning and maintenance.  Just peel them off their backing and stick them to a cleaned frame.

Size: Precise size to fit the insert area on the Scout frame below the seat

Material: A material originally made for motocross, these decals can really take a beating. They are not your everyday "sticker".  These decals are printed on a hi-tack vinyl with a heavy-duty gloss laminate.  It is weather proof, temperature and UV resistant, and will maintain its quality for years.

Shipping times: In-stock products ship the same business day before 9AM or the following business day.  Special Order items must be ordered from our manufacturer and may require up to 2 weeks lead time before we can ship them to you.

What is included:  Matching set of left and right facing decals.

How to Install: Visit our How-To page for videos on the Dry install and Wet Install methods

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Viking 001” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 3.8 x 5 inches each (Set of left and right facing decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Stock Notice:

All style options for our Powerplus Engine Accent kits are usually in stock. However, they are produced in manufacturing runs so if they're out of stock at the time of your order, there may be a waiting period before we ship them out. If your order is time sensitive, feel free to contact us to check stock before ordering.

Engine accent kits for Indian Challenger and Pursuit, Powerplus Chieftain, and Powerplus Roadmaster.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 41 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a 17.5" backing sheet with with a transfer layer on top.

We're offering these in a stunning 20 different color combination styles, but if we don't have the combo you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place. Because the surface is curved, the “I” will be the most challenging piece, so cut out around it as closely as possible to make it easier to position.

Stock Notice:

All style options for our Powerplus Engine Accent kits are usually in stock. However, they are produced in manufacturing runs so if they're out of stock at the time of your order, there may be a waiting period before we ship them out. If your order is time sensitive, feel free to contact us to check stock before ordering.

Engine accent kits for Indian Challenger and Pursuit, Powerplus Chieftain, and Powerplus Roadmaster.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 41 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a 17.5" backing sheet with with a transfer layer on top.

We're offering these in a stunning 20 different color combination styles, but if we don't have the combo you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place. Because the surface is curved, the “I” will be the most challenging piece, so cut out around it as closely as possible to make it easier to position.

New Item - Special Order (may take up to two weeks before shipping)

“Dragon Warrior” Frame Inserts

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Size: Covers the full tank side of ALL Indian Scout models

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install larger decals:  A spray bottle with water and dish soap can be used to wet the tank and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use a squeegee or some non-abrasive tool (even your fingers) to push the moisture out from behind the decal and it will adhere to your tank. 

Companion Product

Check out this matching set!

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

New Item - Special Order (may take up to two weeks before shipping)

“Navy” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Skull Warbonnet (color)” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice:

All style options for our Powerplus Engine Accent kits are usually in stock. However, they are produced in manufacturing runs so if they're out of stock at the time of your order, there may be a waiting period before we ship them out. If your order is time sensitive, feel free to contact us to check stock before ordering.

Engine accent kits for Indian Challenger and Pursuit, Powerplus Chieftain, and Powerplus Roadmaster.

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 41 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a 17.5" backing sheet with with a transfer layer on top.

We're offering these in a stunning 20 different color combination styles, but if we don't have the combo you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place. Because the surface is curved, the “I” will be the most challenging piece, so cut out around it as closely as possible to make it easier to position.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

CLEARANCE

NO REFUNDS - BUY AT YOUR OWN RISK - EXPLANATION FOLLOWS:

After multiple reports from customers, I’ve discovered that the factory finishing process on the Scout engines varies more than anticipated. While the black-coated surface is consistently present, the bare metal accents are manually ground down at the factory, and the level of grinding differs significantly from bike to bike. This results in variations in width, length, and positioning that I hadn’t encountered in other motorcycle models using the same accent kit design.
When I originally created the template, I used an in-shop Scout engine as the reference, but because of the inconsistent factory finishing, some customers are experiencing partial exposure of the bare metal accents beyond the kit’s coverage area. Additionally, the left-side horizontal accents on many Scouts are shorter than the right side by approximately 12-14mm, which required a unique two-piece installation approach. While that adjustment worked in many cases, the additional issue of varying grinding depths has made it impossible to ensure a consistent, proper fit for all bikes.
Because of this, I’ve made the difficult decision to discontinue this product for the Scout lineup to avoid further frustration. Some customers get a perfect fit. Others may find that some of the bare metal is still visible.

_________

By popular demand, we are now making engine accent kits for the Scout like we have been doing for the Challenger and Pursuit.

Engine accent kits for 2014-2024 models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 10% off both v-covers

Fits the Indian Powerplus engine found on the Challenger, Pursuit, Powerplus Chieftain, and Powerplus Roadmaster models.

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Special Order Item (may not always be in stock and could take approximately two weeks before shipping)

“SWB-122” 5 inch Decal

These decal inserts have a 5 inch diameter which makes them a perfect fit for the Thunderstroke engine airbox (for models with a round emblem).  Check out the photos, and if your bike has the same style airbox, these are a match!  

Size: 5 inch diameter circle

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

 EXAMPLE PLACEMENT

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Zombie Hands 001” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 Inches each (set of left and right decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Viking 001” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 3.8 x 5 inches each (Set of left and right facing decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Tentacles 279” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 3 x 5 inches

Gloss Finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.