Hellish Designs

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 20% off both v-covers

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Gloss pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Material: weatherproof laminated heavy-duty vinyl with hi-tack adhesive.  Easy to install using the wet method.

Size: Fill the mentioned insert areas of the frame on the Indian Scout

Add-On set items

Add the matching companion set of tank decals to your order and get 20% off! Click the image below to see this product

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4.5 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 20% off both v-covers

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

We usually have this product in stock and can ship right away but there can be a wait if it sells out before the restock arrives.

Buy 2 and get an automatic 20% off both v-covers

This premium finish badge cover takes minutes to install and provides a completely custom look.  They fit both the left and right v-cover so if you haven't removed the right side cover for another intake, don't forget to grab two!

The v-cover decals are heavy-duty 12 mil laminated gloss vinyl that flow over the curves of the badge for a bespoke custom look.

These self-adhesive decals are applied by hand to the 1901 badge.  If you've already removed the badge, you can use poster putty to fill in the embossed letters before applying our decal over it.

Installation: Be sure your v-cover badge is clean before installing the decal.  Peel the decal off of the backing sheet, careful not to touch the adhesive side of the decal too much.  Carefully align it to a centered position (the decal is slightly smaller than the badge).  Press the decal firmly down in the center to stick it in place, then use your thumbs to push out from the center to the edges.  Repeat this process until you've stretched/pressed it firmly down around the curves.  And that's it!

 How-to Video:

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Zombie Hands 001” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 Inches each (set of left and right decals)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

New Item - Special Order (may take up to two weeks before shipping)

“Zombie Hands 001” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 Inches each (set of left and right decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

These decal inserts adorn the Indian Scout frame near the fork, the mid-frame, and for bobbers, there's an insert for the rear fender (feel free to use this insert somewhere else if your Scout is not a bobber.  

Material: weatherproof laminated heavy-duty vinyl with hi-tack adhesive.  Easy to install using the wet method.

Size: Fill the mentioned insert areas of the frame on the Indian Scout

Add-On set items

Add the matching companion set of tank decals to your order and get 20% off! Click the image below to see this product

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Zombie Hands 002” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: ~6 inches long each (set of 4 decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Zombie Hands 002” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: ~6 inches long each (set of 4 decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.