Accent Decals and Emblems

New Item - Special Order (may take up to two weeks before shipping)

“Dreamcatcher DC420” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 3.7 x 5 inches

Gloss Finish pictured above

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Dreamcatcher DC420” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 3.7 x 5 inches

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Gloss pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

Wolf Paw Print Accent Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4 paw prints at 2" in height. 5 paw prints at 1.5" in height

These decals are a direct-to-film DTF graphic kit that comes with a transfer layer on top that makes it easy to apply them. They are all black with no background color and have an enamel-like finish.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 181” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 4.5 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

ABOUT THIS COLOR: Sunset Red Smoke is not a matte finish since that is impossible with DTF graphics like these accent kits. However, it is a slightly altered version of Sunset Red so that it matches more closely to the "smoke" version of the paint job. This color was sampled directly from the official website color selection.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Zombie Hands 001” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 Inches each (set of left and right decals)

Matte finish pictured above

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Zombie Hands 001” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 Inches each (set of left and right decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

Usually in stock - (if not in stock at time of order may take approximately two weeks before shipping)

“Devil Girl Pin-up 170” Anywhere Decal

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: 2.4 x 5 inches each (set of left and right facing)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

Oracal 651 Vinyl - plotter cut

Engine accent kits for 2025 and up year models of Indian Scout

Dress up your Scout engine with our vinyl engine accent kits. These are plotter cut from Oracal 651 vinyl, a non-printed hi-tack adhesive vinyl available in a wide range of colors. These vinyl cut accents are an even cheaper budget friendly alternative to our premium DTF engine accents.

Kit includes a total of 36 pieces. Your engine requires four "I" logos and 16 accent trim pieces to dress up all the bare metal accents. This kit comes with 32 accent trim pieces (extras included) and four "I" logos. They are provided on two vinyl sheets, one for the right and one for the left. The example below shows what you will receive. The image on the left has the extra background material removed so you can more easily see the pieces of the kit. The shipped product will not have the background removed because it is easier to just peel and stick the individual accent pieces. The following image is a close up detail of the cut sheet.

 Installation: 

Peel and stick after cleaning the engine surface to be free of any dirt and grime.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

PRE-ORDER

New product launch: There will be a brief period of incoming orders before they are manufactured so we will know which colors and quantities to order. If you order, please be patient and we will ship as soon as possible. The more orders we receive, the faster we can make these happen for you.

We are now making engine accent kits for the new 2025 and up models of Scout like we have been doing for the Challenger, Pursuit, and previous year model Scouts.

Engine accent kits for 2025 and up year models of Indian Scout

Our UV DTF 3D PermaSticker Engine Accent kits combine the latest UV DTF technology with exceptional adhesive properties, ensuring that your accents will stick around for the long haul. With unparalleled durability, remarkable adhesive properties, and heat resistance capable of direct contact with your engine, they're the perfect material to add a custom touch to your bike.

Kit includes a total of 48 pieces. All the accents you need to do both sides of your engine AND plenty of extras in case you make a mistake during installation. + 2 Brave Wolf logos. The kit comes on a backing sheet with with a transfer layer on top.

We're offering these in several color styles, but if we don't have the color you want, consider purchasing multiple sets to mix-and-match and you'll save 20% on each. We've priced them affordably so this should be an option.

Material Finish: an enamel-like finish. I wouldn't classify it as gloss or matte. Similar to egg-shell finish.

 Installation: 

This video shows installation on an Indian Challenger but the process is the same on the Scout.

These accents will need to be installed on a warm, clean, and dry engine. Do not attempt to install them cold or with condensation on the surface. You can run your bike to get the engine warm, but not hot, or use a hair dryer/heat gun. Installing these in winter months will be more difficult. Use scissors to separate each individual piece from the sheet. A pair of tweezers can be helpful to hold the accents in proper placement during installation. Once in place, use a firm object to press/rub over the full surface before peeling off the top transfer layer. Go slow while peeling the transfer layer. If the accent peels up without separating from the transfer, place it back down and press it more firmly into place.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Zombie Hands 002” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: ~6 inches long each (set of 4 decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.

Stock Notice - Usually in stock (may take approximately 2-3 weeks before shipping if not in stock at time of order)

“Zombie Hands 002” Anywhere Decal Set

These decals are meant to be used anywhere.  We wanted to provide more options that allow you to customize the look of your bike while using the same high-quality materials we use for our tank and saddlebag decals.

Size: ~6 inches long each (set of 4 decals)

Weatherproof laminated decals are self adhesive.  We recommend using the wet method to install these decals:  A spray bottle with water and dish soap can be used to wet the surface and the back of the decal, allowing you to slide the decal into place.  Once you have it aligned properly, use your thumbs to push the moisture out from behind the decal, working from the center outwards to the edges and it will adhere to your bike.  Using the wet method allows the decal surface to evenly distribute over the curved surface.  A hair dryer to apply heat will make the process easier since the vinyl becomes more soft and flexible when warm.