Motorcycle Protective Gear

All Hot Leathers patches feature a heat- sealed backing. This means that our patches may be ironed on or sewn on to most clothing easily.

Patch Sewing Instructions:

Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.

• • Identify where you want the patch and outline the area with tailor’s chalk
• • Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
  • • Position your inside hand so it is resting flat between the lining and outlines area
  • • Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
• • Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
  • • This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
• • Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
• • Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
• • Finally restitch the garments lining and your all set

Patch Iron-on Instructions:

• • Preheat your iron to 325-335 degrees. Do Not Use Steam.
• • Press the area where you want your patch to be for 25 seconds
• • Position the patch on the garment so that it is positioned where you would like it to be
• • Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure ron the area for 15 seconds
• The iron should never come into direct contact with the patch
• • Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
• • Turn the garment right side in once more, use your clen lightweight cloth to cover the patch
  • • Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
• • Let the garment cool completely before wearing

• Fingerless
• Padded Palm
• Unlined
• Hook and Loop Fastener Adjustable Wrists
• Sizes: XS-2XL

These classic Hot Leathers brown fingerless gloves are unlined with a padded palm are unlined with a padded palm.  Perfect for warm weather riding.

Leather Fingerless Riding Gloves

Don't Tread on Me Design w/ double layer Polyester

Supple Perforated Leather Padded Palm

Leather Knuckle Reinforcement 

• Soft, Naked Leather
• Knuckle Guard
• Perforated Back
• Reinforced Leather Palm
• Sizes: XS-2XL

These black, soft naked leather gloves from Hot Leathers have a perforated back, knuckle guard and a reinforced leather palm.

• Fingerless
• Padded Palm
• Unlined
• Hook and Loop Fastener Adjustable Wrists
• Sizes: XS-3XL

These classic Hot Leathers leather fingerless gloves are unlined and have a padded palm. Perfect for warm weather riding.

Leather Fingerless Riding Gloves

American Flag Design w/ double layer Polyester

Supple Perforated Leather Padded Palm

Leather Knuckle Reinforcement 

• Genuine USA Deerskin
• Shortie Design
• Sizes: S-2XL

These Hot Leathers black "shortie" gloves are made of genuine USA deerskin and are perfect for everyday riding.

All Hot Leathers patches feature a heat- sealed backing. This means that our patches may be ironed on or sewn on to most clothing easily.

Patch Sewing Instructions:

Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.

• • Identify where you want the patch and outline the area with tailor’s chalk
• • Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
  • • Position your inside hand so it is resting flat between the lining and outlines area
  • • Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
• • Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
  • • This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
• • Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
• • Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
• • Finally restitch the garments lining and your all set

Patch Iron-on Instructions:

• • Preheat your iron to 325-335 degrees. Do Not Use Steam.
• • Press the area where you want your patch to be for 25 seconds
• • Position the patch on the garment so that it is positioned where you would like it to be
• • Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure ron the area for 15 seconds
• The iron should never come into direct contact with the patch
• • Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
• • Turn the garment right side in once more, use your clen lightweight cloth to cover the patch
  • • Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
• • Let the garment cool completely before wearing

All Hot Leathers patches feature a heat- sealed backing. This means that our patches may be ironed on or sewn on to most clothing easily.

Patch Sewing Instructions:

Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.

• • Identify where you want the patch and outline the area with tailor’s chalk
• • Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
  • • Position your inside hand so it is resting flat between the lining and outlines area
  • • Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
• • Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
  • • This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
• • Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
• • Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
• • Finally restitch the garments lining and your all set

Patch Iron-on Instructions:

• • Preheat your iron to 325-335 degrees. Do Not Use Steam.
• • Press the area where you want your patch to be for 25 seconds
• • Position the patch on the garment so that it is positioned where you would like it to be
• • Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure ron the area for 15 seconds
• The iron should never come into direct contact with the patch
• • Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
• • Turn the garment right side in once more, use your clen lightweight cloth to cover the patch
  • • Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
• • Let the garment cool completely before wearing

• Top Grain Waterproof Leather
• Slip Resistant
• Oil Resistant Sole
• Antiqued Silver Hardware & YKK® Zippers
• Smart-Mask® Performance Insole
• Non-Marking Heat Resistant Lug Sole
• Speed Lacing

Hot Leathers is proud to present our new Riding Collection of motorcycle boots for men and women. Hot Leathers Riding Collection is a growing line of the absolute highest quality leather boots made specifically for motorcycling. Each of these motorcycle boots are handcrafted by highly skilled craftsmen and women who know what it takes to make long lasting quality footwear. All of these riding boots are water proof and slip resistant and using heavy duty hardware and YKK® zippers. Hot Leathers biker boots come with a 30 day warranty and a hassle free exchange policy. Order yours today!

All Hot Leathers patches feature a heat- sealed backing. This means that our patches may be ironed on or sewn on to most clothing easily.

Patch Sewing Instructions:

Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.

• • Identify where you want the patch and outline the area with tailor’s chalk
• • Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
  • • Position your inside hand so it is resting flat between the lining and outlines area
  • • Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
• • Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
  • • This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
• • Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
• • Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
• • Finally restitch the garments lining and your all set

Patch Iron-on Instructions:

• • Preheat your iron to 325-335 degrees. Do Not Use Steam.
• • Press the area where you want your patch to be for 25 seconds
• • Position the patch on the garment so that it is positioned where you would like it to be
• • Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure ron the area for 15 seconds
• The iron should never come into direct contact with the patch
• • Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
• • Turn the garment right side in once more, use your clen lightweight cloth to cover the patch
  • • Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
• • Let the garment cool completely before wearing

• Top Grain Waterproof Leather 
• Slip Resistant 
• Oil Resistant Sole 
• Antiqued Silver Rivets 
• Non-Marking, Heat Resistant Sole 
• Double Stitched Upper

Hot Leathers is proud to present our new Riding Collection of motorcycle boots for men and women. Hot Leathers Riding Collection is a growing line of the absolute highest quality leather boots made specifically for motorcycling. Each of these motorcycle boots are handcrafted by highly skilled craftsmen and women who know what it takes to make long lasting quality footwear. All of these riding boots are waterproof and slip resistant and using heavy duty hardware and YKK® zippers. Hot Leathers biker boots come with a 30 day warranty and a hassle free exchange policy. Order yours today!

• Top Grain Waterproof Leather
• Slip Resistant
• Oil Resistant Sole
• Silver Rivets
• Non-Marking, Heat Resistant Sole
• Double Stitched Upper

Hot Leathers is proud to present our new Riding Collection of motorcycle boots for men and women. Hot Leathers Riding Collection is a growing line of the absolute highest quality leather boots made specifically for motorcycling. Each of these motorcycle boots are handcrafted by highly skilled craftsmen and women who know what it takes to make long lasting quality footwear. All of these riding boots are waterproof and slip resistant and using heavy duty hardware and YKK® zippers. Hot Leathers biker boots come with a 30 day warranty and a hassle free exchange policy. Order yours today!

All Hot Leathers patches feature a heat- sealed backing. This means that our patches may be ironed on or sewn on to most clothing easily.

Patch Sewing Instructions:

Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.

• • Identify where you want the patch and outline the area with tailor’s chalk
• • Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
  • • Position your inside hand so it is resting flat between the lining and outlines area
  • • Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
• • Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
  • • This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
• • Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
• • Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
• • Finally restitch the garments lining and your all set

Patch Iron-on Instructions:

• • Preheat your iron to 325-335 degrees. Do Not Use Steam.
• • Press the area where you want your patch to be for 25 seconds
• • Position the patch on the garment so that it is positioned where you would like it to be
• • Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure ron the area for 15 seconds
• The iron should never come into direct contact with the patch
• • Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
• • Turn the garment right side in once more, use your clen lightweight cloth to cover the patch
  • • Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
• • Let the garment cool completely before wearing

• Top Grain Waterproof Leather
• Slip Resistant
• Oil Resistant Sole
• Non-Marking, Heat Resistant Mini Lug Sole
• Double Stitched Upper
• Antiqued Silver YKK® Zippers

Hot Leathers is proud to present our new Riding Collection of motorcycle boots for men and women. Hot Leathers Riding Collection is a growing line of the absolute highest quality leather boots made specifically for motorcycling. Each of these motorcycle boots are handcrafted by highly skilled craftsmen and women who know what it takes to make long lasting quality footwear. All of these riding boots are waterproof and slip resistant and using heavy duty hardware and YKK® zippers. Hot Leathers biker boots come with a 30 day warranty and a hassle free exchange policy. Order yours today!

• 7" side zippered 
• Waterproof 2.2 mm top grain enter 
• Slip resistant and oil resistant sole 
• Goodyear wear construction
• YKK Zipper 
• Gun metal stud detail

Great for riding or styling. This pair has all the features you need for riding and fun when at your destination. 

All Hot Leathers patches feature a heat- sealed backing. This means that our patches may be ironed on or sewn on to most clothing easily.

Patch Sewing Instructions:

Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.

• • Identify where you want the patch and outline the area with tailor’s chalk
• • Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
  • • Position your inside hand so it is resting flat between the lining and outlines area
  • • Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
• • Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
  • • This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
• • Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
• • Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
• • Finally restitch the garments lining and your all set

Patch Iron-on Instructions:

• • Preheat your iron to 325-335 degrees. Do Not Use Steam.
• • Press the area where you want your patch to be for 25 seconds
• • Position the patch on the garment so that it is positioned where you would like it to be
• • Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure ron the area for 15 seconds
• The iron should never come into direct contact with the patch
• • Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
• • Turn the garment right side in once more, use your clen lightweight cloth to cover the patch
  • • Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
• • Let the garment cool completely before wearing

All Hot Leathers patches feature a heat- sealed backing. This means that our patches may be ironed on or sewn on to most clothing easily.

Patch Sewing Instructions:

Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.

• • Identify where you want the patch and outline the area with tailor’s chalk
• • Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
  • • Position your inside hand so it is resting flat between the lining and outlines area
  • • Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
• • Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
  • • This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
• • Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
• • Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
• • Finally restitch the garments lining and your all set

Patch Iron-on Instructions:

• • Preheat your iron to 325-335 degrees. Do Not Use Steam.
• • Press the area where you want your patch to be for 25 seconds
• • Position the patch on the garment so that it is positioned where you would like it to be
• • Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure ron the area for 15 seconds
• The iron should never come into direct contact with the patch
• • Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
• • Turn the garment right side in once more, use your clen lightweight cloth to cover the patch
  • • Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
• • Let the garment cool completely before wearing